On this page
On food and drink sites, contractors create three kinds of risk: harm to people, harm to the environment and harm to the food itself. A loose screw, a fragment of glass, a contaminated tool or poor hand hygiene can lead to a product recall as well as an injury. Food manufacturers control this with hygiene rules, tool and material controls, zoned access and supervision, and many ask contractors to hold the SPA Food and Drink passport, which covers food protection, environmental protection and health and safety in the food industry.
Why food sites are different
Most contractor safety thinking is about protecting people from hazards. Food sites add a second direction: protecting the product from the contractor.
A maintenance engineer working above a production line, a builder working near an open process or a cleaner using the wrong chemical can contaminate food. The consequences include customer illness, product recalls, lost contracts and damage to the brand. A single foreign body complaint can cost a manufacturer far more than the job the contractor was there to do.
The SPA Food and Drink passport was written for this. It describes the three main areas of concern on a food site as food damage, environmental damage and people damage.
The main contamination risks from contractors
| Type | Examples from contractor work | Typical controls |
|---|---|---|
| Physical | Screws, nuts, swarf, wire, glass, paint flakes, wood splinters, plastic fragments | Tool and parts checklists, swarf control, covering open product, post-work clean-down and inspection |
| Chemical | Lubricants, cleaning chemicals, paints, solvents, fuel | Approved food-grade lubricants, controlled chemical storage, no unapproved products in production areas |
| Microbiological | Dirty hands, clothing or tools, drains opened during work, pests attracted by gaps or debris | Handwashing, protective clothing, hygiene zoning, sealing openings, pest control checks |
| Allergens | Food brought onto site, cross-contact between areas | Rules on food and drink, segregated areas, clean-down between zones |
How food manufacturers control contractors
Hygiene rules. Protective clothing, hairnets, no jewellery, handwashing at entry points and rules about food and drink on site.
Zoned access. Many sites divide production into zones by risk, with stricter rules in high-risk or high-care areas. Contractors may need to change clothing or footwear and pass through hygiene stations between zones.
Tool and material control. Tools are listed in and out, glass and brittle plastics are controlled, and swarf and debris are contained.
Engineering hygiene. After maintenance, the area is cleaned, inspected and signed off before production restarts.
Permits and isolation. Higher-risk work, including work on machinery and hot work, is controlled through permits and isolation procedures.
Supervision. Contractors are accompanied or supervised according to the risk of the work and the zone.
Audit standards used across the industry, such as BRCGS, expect food manufacturers to control contractors and visitors, which is one reason passport requirements are common.
What the SPA Food and Drink passport covers
Day one: the SPA Core Day. Organising for safety, the workplace, tools, plant and machinery, health, procedures and the environment.
Day two: Food and Drink.
- Food protection: the potential sources and types of contamination, their effects, safe working practices to eliminate or reduce the risk, protective clothing and personal hygiene.
- Environmental protection: current and future environmental requirements, the impact of environmental damage, pollution controls and proper waste disposal.
- Health and safety: the hazards most relevant to food and drink manufacturing and the control measures that keep reducing them.
The course also looks at injury rates across sectors, the importance of good personal behaviour, and the cost, job security and injury implications when concerns are not controlled. The passport lasts three years and is renewed with a one-day refresher. About the Food and Drink passport.
Introducing a passport requirement on a food site
Food manufacturers have used SPA passports for contractors for many years. When United Biscuits introduced its requirement, it wrote to 600 contractor organisations to say they would need to present safety passports before starting work on its sites. The food industry's own steering committee also produced guidance on implementing the scheme based on members' experience.
If you are introducing a requirement:
- Write it into your contractor conditions and give your supply chain notice.
- Check cards on arrival, including the Food and Drink sector and its expiry date.
- Keep your site induction for your own hygiene zones, rules and emergency arrangements.
- Use your engineering hygiene and permit procedures as normal.
- Review how contractor work affects product safety, using your incident and complaint records.
Our employer guide covers the steps in more detail.
A contractor's checklist before entering a food site
- My Food and Drink passport is in date and I have it with me
- I have the site's hygiene rules and know which zones I will enter
- My tools and parts are listed, clean and suitable for the area
- Any lubricants or chemicals I bring are approved by the site
- I know how swarf, debris and packaging will be contained and removed
- I know whether the job needs a permit and who will issue it
- I have no food, drink or jewellery with me in production areas
- I know how the area will be cleaned and signed off after the work
Common contractor mistakes on food sites
Leaving debris behind. Swarf, screws, cable ties and packaging are the classic foreign bodies. Count parts in and out, and leave the area cleaner than you found it.
Bringing in unapproved products. A general-purpose lubricant or cleaner can contaminate product. Use only what the site has approved.
Ignoring zone rules. Walking from a low-risk area into a high-care area without changing or washing can spread contamination.
Opening drains or panels without telling anyone. Drains and voids can harbour bacteria and pests. Check before you open anything.
Restarting equipment too soon. Production should only restart after the site's hygiene clean-down and sign-off.
Frequently asked questions
Do contractors need a passport to work in food factories?
It depends on the manufacturer. Many food and drink manufacturers ask contractors for the SPA Food and Drink passport before they enter production areas.
What does the Food and Drink passport cover?
The SPA Core Day plus a sector day on food protection, environmental protection and health and safety in food and drink manufacturing.
Is the Food and Drink passport a food hygiene certificate?
No. It is a health and safety passport for the food and drink industry that includes food protection. Roles handling food may need separate food hygiene training.
How long does the Food and Drink passport last?
Three years. It is renewed with a one-day refresher in the six months before expiry.


